Both seats LH and RH

Seat covers sold in pairs only Note: Upper LH corner seat cover in photo has been flipped over to show the back detail. Single photo of bottom portion of seat is a close up view of the original looking diamond pattern center vinyl section. Click here, for the head rest covers. Click here, to view red seat cover set.

New Revamped 68-70 Soft Top Header Bow Finisher. You may wish to install this when you're putting on a new top as it will go on easier before installation. This hard plastic finisher mounts on the front bow of your soft top frame and is a wonderful cosmetic addition to the assembly. Easy fit and assembly. Just drill the holes for your soft top clamps, glue in and you are done! This photo is what arrives at your doorstep.

Check out the before assembly and after assembly in photos #1077 and #1078.

This is an easy-to-assemble, UV resistant hard plastic vacuform skin you can put over your original console to make it like new. This is what shows up at your doorstep so you can recover your console.click here, and click here, for before and after installation photos. Purchase separately or save bundles on our new 4-piece vacuuform interior kit listed in specials dated Feb. 9th 2002. Over 900 of these covers have been sold and installed. Work is required for fitting. If you do not have the patience, skill to trim, file and fit these vacuform parts please hire a installer to assist you.

46 pieces included in this kit does all the panels. click here, for individual cost open stock pieces.

Beautiful Reproductions. Hole diameter in visors match the original rods. No need to open. Correct fitting. Re-use your old hardware. Call us prior to installing your rods for some helpful instructions. Available in colors. See swatch. Click here,to view complete hardware kit.

Use a soldering iron set to low heat and carefully open the heat seamed ends of the assembly to install the hardware.

Accurate well-constructed replacement sun visors. Hole diameter in visors matches original sun visor rods. Correct fitting. No need to open. Re-use your old hardware.

Use a soldering iron set to low heat and carefully open the heat seamed ends of the assembly to install the hardware.

Round out your restoration with these beautiful, faithfully reproduced seat covers. Remember all our seat covers are available in different colors. You choose, not us. (see color swatch) Click here, to view red seat cover set.

Impeccable detail. Faithful diamond pattern reproduction vinyl. By the way, our vinyl is state-of-the-art modern diamond pattern vinyl. Not old, dried up stock. Heavy-duty construction. click here, for 67 1/2 seat cover set.

Beautiful, well-made with waterproof panel board. These glove boxes require skill in assembly.

Beautiful, well-made with waterproof panel board. These glove boxes require skill in assembly.

Our carpet sets are well-crafted and precisely-fitted.

They are available in plush and loop materials and come with CUSTOM DIE-CUT jute pad and have bound edges.

SPECIAL NOTE 7/07/08: All loop kits are now made with a heavy duty loop variant not often available from regular supliers. We opted for this better quality material that last longer than regular kits.

Of course, we have color swatches we can send to you with a variety of colors to choose from. Set shown is a 8 piece set includes trunk and back shelf option piece. We prefer not to cut out for the E-brake assembly or for the shifter linkage. We know it is not original, but we feel it looks cleaner this way. Want bound edges around these areas? Just ask. NOTE: Last piece in the photo is for the rear shelf. It is included in this set to protect the vinyl area. Do not glue it on the vinyl. Keep it in the trunk and use it when you are transporting items that may scratch or damage the vinyl shelf piece. It is the eighth piece in the set and there is no extra charge for it so you can simply throw it away if the look doesn't work for you. Other photos show the installation of a loop set.

See swatch for other colors. Note: Colors other then red have black bound edges.Click here then scroll down through vinyl swatches to carpet swatches.

Click here, to view Wilton Wool Set.

This dash cap fits great or purchase our beautiful foam repro also pictured in our interior section. Purchase this dash cap separately or save bundles on our 4-piece vacuuform interior kit. See specials section for great kit prices and combos.

Click here, to view the RH drive version of this dash.

You've seen our wonderful 65-67 model foam dashes. Featured on Award Winning cars at the Mt. Shasta meet. Now high windshield fans can install an eye-popping dash on their cars too. Same quality reconstruction and attention to detail that the others can only copy, make this new arrival the only one of its kind in the serious-minded world of quality restorations. Glove box door is optional. Call us for more details. For vacuformed dash caps, click here12/14/07

Top View of 1222.

Door panels sold in pairs only! All Panels come assembled with water proof panel board click here, for pleated pocket variants.

Seat covers are sold in pairs. LH top seat cover has been flipped over to show the back detail. See part# 1238 for head rest covers. Click here, to view black seat cover set.

Can't afford our original style seat covers? Why not buy our NEW not old dried up original diamond pattern vinyl? Great quality and available in white for those of you who wish to dye your vinyl for custom colors!

Seat covers with original diamond pattern vinyl and authentic pattern. LH and RH both tops and bottoms.These beauties will finish off your '67 2000! Heavy duty construction quality stitching. The top LH seat cover has been flipped to show the back detail. click here, for photo of 67-1/2 headrests.

Petroleum based ArmorAl can dry out vinyl parts in your interior. We are proud to now offer a silicone protectant to keep your vinyl interior parts supple and conditioned.

Dress up your 65-67, 67 1/2 model Dash facia with a Carbon Fiber/Rosewood/Burled Elm face plate. Rosewood shown. Easy to install. REAL wood with High Gloss Hard Resin Finish! Yes you can still install your dash trim ring!

Photo is of the 65 - 67 Early dash faceplate.

Dress up your 65-67, 67 1/2 model dash facia with a Carbon Fiber/Rosewood/Burled Elm face plate. Carbon Fiber shown. Easy to install! Comes with high-gloss finish! Yes, you can still install your dash trim ring!

Never ever available before as separate pieces!

Why pay over $240.00 for new handles just to get these inserts?

These original looking inserts really finish off the restoration. Don't hold back and miss the details of your restoration and settle for "sub par fix it's" and band aids! Metal door handle receptacle shown for assembly reference only.

Back side view shown in first photo. There were different versions of this plastic insert. The one we have is the most common and adaptable version.

Original assembly of these required the pin to be peened over to fasten it to the door opener. Clear silicon works quite well in holding the finisher in position.

LT

No!! You're not looking at a mirror image or a flipped negative of a 68-70 regular LH Drive Dash Cap. It's a Righty. We have it....it's here...long awaited for the lads down under and collectors of RH drive cars all over the world...!!! A custom made mold RH Drive Vacuformed Dash cap.