Our carpet sets are well-crafted and precisely-fitted.NOTE:Carpet kits are used for both the 1600 and 2000. The shifter area is not cut out as the 4 speed and the 5 speed locations are in different positions.

DEFAULT KIT COMES WITH THE CARPET PIECE FOR THE JACK ON THE BACK WALL. Please specify when ordering if your car Jack is located on the back wall or on the side in the left wheel well.
(((SEE DRAWING IN PHOTO)))

CUSTOM DIE-CUT jute pad. Carpet has bound edges.

If you decide not to glue in the carpet you can, as an add on purchase as the fasteners are not included, order our 20 piece anodized black, carpet fasteners with stainless steel mating floor snaps. 8 for each side of for the front and rear floor pieces and 4 for the trunk carpet. Part# 2573

Impeccable detail. Faithful diamond pattern reproduction vinyl. By the way, our vinyl is state-of-the-art modern diamond pattern vinyl. Not old, dried up stock. Heavy-duty construction. click here, for 67 1/2 seat cover set.

Our carpet sets are well-crafted and precisely-fitted.NOTE:Carpet kits are used for both the 1600 and 2000. The shifter area is not cut out as the 4 speed and the 5 speed locations are in different positions.

DEFAULT KIT COMES WITH THE CARPET PIECE FOR THE JACK ON THE BACK WALL. Please specify when ordering if your car Jack is located on the back wall or on the side in the left wheel well.
(((SEE DRAWING IN PHOTO)))

CUSTOM DIE-CUT jute pad and the carpet has bound edges.

If you decide not to glue in the carpet you can, as an add on purchase as the fasteners are not included, order our 20 piece anodized black, carpet fasteners with stainless steel mating floor snaps. 8 for each side of for the front and rear floor pieces and 4 for the trunk carpet.Part# 2573

Of course, we have color swatches we can send to you with a variety of colors to choose from. Set shown is a 7 piece set includes trunk piece.

Replaces 63 - 69 Idler shaft with top washer & 69 1/2 - 70 without washer. No it is not necessary to have the top washer for early steering boxes!
Manufactured by the same company that made our upper ball joints that are Rare Parts Approved
This company also makes parts for IMC and World Pac
Responsibly sourced. Approved by Mark Degroff who has rebuilt hundreds of idler box assemblies for the Datsun community

NOT CHINESE

When purchased in the Major Idler box rebuild kit price for the shaft is $40.00 SEE this section for the major kits early and late

Good used shafts checked and approved by Mark Degroff original Nissan Early & Late Idler shafts.
From our stock yours will look the same if not better.
ORDER BY PART# 1139EARLYNISSAN $110.00
ORDER BY PART# 1139LATENISSAN $110.00

Elliot Harvey Racing: "NEW IDLER SHAFT, NICE HIGH QUALITY PART"

These piston sets can also be used on U20 Motors. Limited Supply. You blow off the dust. Complete with pins, rings, and cir-clips. The original piston sets came with the older style round "wire type" which are less preferable. Pins are pre-fitted.

NOTE: Piston to wall clearance: .0015 to .003 measured from the highest point of the taper on the piston skirt.

Sizes:

Std. - Order by PART# #1189A$600.00

.020 - Order by PART#1189B$600.00

.030 - Order by PART#1189C$600.00

.040 - Order by PART##1189D$600.00

.060 - Order by PART# 1189E$780.00

Piston sets are cheaper per set in the full engine rebuild kit section

Click here, for this section

Brand New Planetary/Gear Reduction Starter for all 1600's and 2000's. Easy install no modification required.

There are 2 different versions of this starter. 1 which is longer in length than the other. We have always opt for the shorter version, OVERALL LENGTH 7 1/4 to 3/8 INCHES, for the obvious clearance issues and OURS work with our headers and also AC Industries headers.

Another Datsun Parts first. We were the very first vendor, without question, to offer this starter.

Overshadowing even the U20 starter with superior torque, this unit also features a Bendix gear that pops out, engages the ring gear before it starts turning, thus saving the ring gear teeth from eventual wear. In addition, this unit is fully sealed and enclosed not vulnerable to rear main seal oil spun up on the back side of the flywheel which in un-sealed antique open snout designs, like the 1600 and 2000, usually results in the starter filling up with oil leading to poor electrical contact and brush breakdown. Most of the 1600 and 2000 starters have been around for 30 years having been heated up burnt-to-death and rebuilt 10 or 15 times (which is usually the case). Fits with all brands of headers.

1 year warranty regular Su and Solex cars as of 8/6/08

All our starters work with the original exhaust manifold and headers

Door panels sold in pairs only! All Panels come assembled with water proof panel board click here, for pleated pocket variants.

Seat covers are sold in pairs. LH top seat cover has been flipped over to show the back detail. See part# 1238 for head rest covers. Click here, to view black seat cover set.

Seat covers with original diamond pattern vinyl and authentic pattern. LH and RH both tops and bottoms.These beauties will finish off your '67 2000! Heavy duty construction quality stitching. The top LH seat cover has been flipped to show the back detail. click here, for photo of 67-1/2 headrests.

We first used a flex pipe on our Solex 67 2000 24 years ago and have been happy ever since! Stainless steel construction allows movement of the motor while the exhaust stays rigid and undisturbed

Our flex pipe, pictured on the blue back round, is longer and wider/NOT restrictive unlike the generic, (short) flex pipe pictured which is similar to what other vendors are selling on the white back round.


Our flex pipe diffuses the exhaust pulse that can be hard on welds in the exhaust system

Flange is precision laser cut. Save all those expensive parts from excessive strain and harmonics. Click here, to view the gasket that goes with this part.

Stainless braided area of the pipe measures 3 inches O.D. The I.D. of exist port of the pipe is 2 inches. Overall length is 8 1/2 inches.